Effects on Patch
Patchulator Pro’s ten numbered channels are primarily used for pedals or effects processors, and allow chains of effects to be created on-the-fly using a few mini patch cables. First, the inputs and outputs of pedals and effects are connected to the send (gray) and return (black) 1/4-inch jacks on the rear of the patchbay. Then using the top 3.5 mm jacks labeled SND and RCV, signals can be routed freely through the effects channels to make a chain.
Alternatively, instrument sources (and destinations) can also connect to any of these ten channels for direct patch access if the dedicated MAIN I/O instrument channel is not enough.
Selectable FX Chain
A new and useful feature of Patchulator Pro is its dedicated instrument channel, which allows for quick access to one of two effects chains.
The 1/4-inch jacks labeled MAIN I/O are the instrument channel’s external input (black) and output (gray). Once connected, the input signal is available on top at both RCV patch points (multiples) within the instrument channel section. These copies can be used to create separate effects chains. Using the included patch cables, each chain is routed through any combination of the ten effects channels, then returned to its respective SND patch point.
The OUTPUT SOURCE switch is used to select which chain is sent to the instrument channel’s main output. Simply slide it all the way to the left or right. With the 3-way switch in the center BYPASS position, the instrument input is sent directly to the output, effectively bypassing both effects chains. This selection is useful to A/B an affected signal against the “dry” signal, and is a foolproof way to avoid pops while patching.
NOTE: Pops can also be avoided while patching by selecting the other chain, as long as the internal jumpers remain in their default OFF state (see Circuit Configuration).
Expert Interconnection
Patchulator Pro is purposefully configured with TRS (Tip, Ring, Sleeve) connections throughout to maximize compatibility with a range of gear and setups. All of the connections, circuitry, and the included patch cables are capable of carrying unbalanced mono, stereo, and/or balanced audio signals.
A single patch cable can carry two signals, thus eliminating the need to use two channels for a stereo patch. A single patch cable can also carry balanced audio signals like those typical of rack compressors, equalizers, and studio effects processors.
Each Patchulator Pro comes ready-to-patch with twelve premium Boredbrain patch cables, enough to use every patch point. The 10-inch cables of two colors (green and black) are customized to reach the full width of the patchbay and to differentiate between the two effects chains.
NOTE: Stereo pedals lacking TRS jacks may require Y-splitter adapters (insert cables).
Pedalboard Effects On Patch
Choose easily which individual pedals are placed into your signal chains and in what sequence. Switch between the two chains instantaneously.
Desktop Instruments & Effects
Intercept signals from your electronic instruments, and easily insert different effects on each instrument, swapping and experimenting as you go.
Warranty & Returns
All New products are covered by the manufacturers new warranty. Please check their website for the length of warranty and warranty conditions. If an item you receive is faulty get in touch with us ASAP. Second Hand products come with a 4 week warranty from us. If there is an issue let us know ASAP! This covers normal use and does not cover accidental damage, misuse, wrong power plugged into it, modding, water damage or any other damage caused by mistreatment. Just treat it nice and all will be good!
Shipping
We send A LOT of packages every week so don't worry about the shipping side of things!
We've never lost a thing and your awesome new gear will be packed up really well to avoid any damage in transit.
If your order comes in before 2pm we will ship it same day. Most of the time we pack things up all the way to 4pm so just call if you need it to leave same day after 2pm.
We ship mainly with Australia Post but may use a courier depending on location and size of the package.
Free Post ships with Australia Post standard and expected shipping times are between 4-6 business days depending on location. It will be longer to outside of metro and rural areas.
Express Post will usually be with you next business day in metro areas of QLD, NSW, SA, VIC and TAS. WA will take 2 days to metro and extra days after that to out side metro and rural areas.
Everything we ship has a tracking number with the exception of some power cables and smaller envelope packages. You will be emailed tracking once your order has been shipped!
Effects on Patch
Patchulator Pro’s ten numbered channels are primarily used for pedals or effects processors, and allow chains of effects to be created on-the-fly using a few mini patch cables. First, the inputs and outputs of pedals and effects are connected to the send (gray) and return (black) 1/4-inch jacks on the rear of the patchbay. Then using the top 3.5 mm jacks labeled SND and RCV, signals can be routed freely through the effects channels to make a chain.
Alternatively, instrument sources (and destinations) can also connect to any of these ten channels for direct patch access if the dedicated MAIN I/O instrument channel is not enough.
Selectable FX Chain
A new and useful feature of Patchulator Pro is its dedicated instrument channel, which allows for quick access to one of two effects chains.
The 1/4-inch jacks labeled MAIN I/O are the instrument channel’s external input (black) and output (gray). Once connected, the input signal is available on top at both RCV patch points (multiples) within the instrument channel section. These copies can be used to create separate effects chains. Using the included patch cables, each chain is routed through any combination of the ten effects channels, then returned to its respective SND patch point.
The OUTPUT SOURCE switch is used to select which chain is sent to the instrument channel’s main output. Simply slide it all the way to the left or right. With the 3-way switch in the center BYPASS position, the instrument input is sent directly to the output, effectively bypassing both effects chains. This selection is useful to A/B an affected signal against the “dry” signal, and is a foolproof way to avoid pops while patching.
NOTE: Pops can also be avoided while patching by selecting the other chain, as long as the internal jumpers remain in their default OFF state (see Circuit Configuration).
Expert Interconnection
Patchulator Pro is purposefully configured with TRS (Tip, Ring, Sleeve) connections throughout to maximize compatibility with a range of gear and setups. All of the connections, circuitry, and the included patch cables are capable of carrying unbalanced mono, stereo, and/or balanced audio signals.
A single patch cable can carry two signals, thus eliminating the need to use two channels for a stereo patch. A single patch cable can also carry balanced audio signals like those typical of rack compressors, equalizers, and studio effects processors.
Each Patchulator Pro comes ready-to-patch with twelve premium Boredbrain patch cables, enough to use every patch point. The 10-inch cables of two colors (green and black) are customized to reach the full width of the patchbay and to differentiate between the two effects chains.
NOTE: Stereo pedals lacking TRS jacks may require Y-splitter adapters (insert cables).
Pedalboard Effects On Patch
Choose easily which individual pedals are placed into your signal chains and in what sequence. Switch between the two chains instantaneously.
Desktop Instruments & Effects
Intercept signals from your electronic instruments, and easily insert different effects on each instrument, swapping and experimenting as you go.
Warranty & Returns
All New products are covered by the manufacturers new warranty. Please check their website for the length of warranty and warranty conditions. If an item you receive is faulty get in touch with us ASAP. Second Hand products come with a 4 week warranty from us. If there is an issue let us know ASAP! This covers normal use and does not cover accidental damage, misuse, wrong power plugged into it, modding, water damage or any other damage caused by mistreatment. Just treat it nice and all will be good!
Shipping
We send A LOT of packages every week so don't worry about the shipping side of things!
We've never lost a thing and your awesome new gear will be packed up really well to avoid any damage in transit.
If your order comes in before 2pm we will ship it same day. Most of the time we pack things up all the way to 4pm so just call if you need it to leave same day after 2pm.
We ship mainly with Australia Post but may use a courier depending on location and size of the package.
Free Post ships with Australia Post standard and expected shipping times are between 4-6 business days depending on location. It will be longer to outside of metro and rural areas.
Express Post will usually be with you next business day in metro areas of QLD, NSW, SA, VIC and TAS. WA will take 2 days to metro and extra days after that to out side metro and rural areas.
Everything we ship has a tracking number with the exception of some power cables and smaller envelope packages. You will be emailed tracking once your order has been shipped!
